During class...
To play a VHS tape…	1. Unlock the padlock on the black cabinet (mounted on the FRONT wall of the classroom).
	2. Align the number wheels on the padlock to the correct combination.
	3. Hold the curved bar with your LEFT hand and the padlock body with your RIGHT hand and push them towards each other to open the lock.
	4. Move the number wheels so no one else will see the combination.
	5. Flip the green "MAIN POWER" switch "UP" to the "ON" position.
	6. Remove the large gray remote control from the cabinet.
	7. Move the remote control's "POWER" switch to the "ON" position (located on the RIGHT side).
	8. Press the "ON" button on the remote control (located on the FRONT) while pointing it towards the video projector mounted on the ceiling.
	9. Press the "VIDEO1" button on the remote control while pointing it at the video projector.
	10. Press the "POWER" button on the VCR.
	11. Insert the tape and press the "PLAY" button on the VCR (unless the tape starts playing automatically).
	12. Adjust the volume by pressing the (5 ) or (6 ) "VOLUME" buttons while pointing it at the video projector.
	13. Stop the tape by pressing the "STOP/EJECT" button on the VCR.
	14. Rewind the tape by pressing the "REW" button on the VCR.
	15. Remove the tape by pressing the "STOP/EJECT" button on the VCR.
To connect your laptop to the Internet…	1. Unlock the padlock on the black cabinet mounted on the wall in the FRONT of the classroom.
	2. Align the number wheels on the padlock to the correct combination.
	3. Hold the curved bar with your LEFT hand and the padlock body with your RIGHT hand and push them towards each other to open the lock.
	4. Move the number wheels so no one else will see the combination.
	5. Flip the green "MAIN POWER" switch in the cabinet to the "ON" position.
	6. Connect your laptop's power cable to your laptop.
	7. Insert the power plug into the electrical outlet (located on the FRONT wall).
	8. Connect one end of a 15-pin VGA cable into the "VIDEO OUT" connection on your laptop (often the correct connection is the only one where it fits).
	9. Connect the other end of the 15-pin VGA cable to the "VIDEO IN" connection labeled "INPUT" (located on the SIDE of the counter near the inside door).
	10. Plug one end of a network cable into your laptop (some laptops come with a special adapter that links the laptop to the network cable).
	11. Plug the other end of the network cable into the network jack with the red tab above it (located to the LEFT of the VGA cable connection).
	*NOTE:* You must set up your laptop to dynamically grab an IP address when you turn on your laptop. If you are unfamiliar with how to do this, contact Susan Campbell (scampbel@osf1.gmu.edu) for help.
To display your laptop's screen on the projection screen in the front of the room…	1. Remove the large gray remote control from the cabinet.
	2. Move the remote control's "POWER" switch to the "ON" position (located on the RIGHT side).
	3. Press the "ON" button on the remote control (located on the FRONT) while pointing it towards the video projector mounted on the ceiling.
	4. Press the "DATA1" button on the remote control while pointing it towards the video projector.
	5. Turn on your laptop.
	6. After the main Windows screen appears on your laptop, check to see whether you can see the same screen displayed from the video projector. If not, then check your manual to see what key or combination of keys you need to press to display the screen on both the laptop and projection screen.
	*NOTE:* Often, you must press the [Fn] key and one of the function keys once or twice. Usually, this function key will have a picture of a monitor on it.
	*NOTE:* If the image on the screen is not centered horizontally on the projection screen, adjust it by turning the blue knob labeled "HORIZONTAL POSITION" (located on the SIDE of the counter close to the inside door near the VGA "INPUT").
To use the slide projector…	1. Open the padlock on the black cabinet mounted on the BACK wall.
	*NOTE:* The combination is the same as the padlock on the cabinet on the FRONT wall. The instructions for how to open the cabinet in front of the room can be found under the "To play a VHS tape…" section above.
	2. Turn the slide projector on by flipping the "POWER" switch "UP" to the "ON" position (located in the cabinet).
	3. Remove the slide projector remote control (located in the cabinet mounted on the BACK wall) to use.