Using Enterprise, rm. 173

Before class...
Step 1: Unlock the outside right door to the room by entering your code into the Omni lock (when you close this door, it will lock automatically). 1. Press the "CLR" button on the Omni lock panel.
2. Enter your code.
3. Press the "CLR" button again.
A green light on the panel will flash.
4. Immediately turn the doorknob to the RIGHT and pull open the door.
Step 2: Adjust the lighting. 1. Flip the light switches next to the door to turn on the florescent lights.
2. Push up the dimmer switches on the far wall (the second and third switch to the RIGHT) to turn on the incandescent lights.
Step 3: Make sure all the Student Computers are "ON."
Step 4: Turn on the Instructor Computer "ON" if it is "OFF" when you enter the room.
Step 5: Project whatever is on the Instructor's screen to the two TV monitors in the front of the room. 1. Press "RIGHT MONITOR POWER" on the Touch Panel.
2. Press "LEFT MONITOR POWER."
3. Press "RIGHT SOURCE."
4. Press "CLASSNET."
5. Press "PREVIOUS MENU."
6. Press "LEFT SOURCE."
7. Press "CLASSNET."
8. Press "PREVIOUS MENU."

 

 

 

During class...
To send the Instructor’s screen to all the students’ screens...
1. Press "FROM" on the Instructor's Control Keypad.
A blinking cursor will appear after the FROM: prompt on the display panel.
2. Press "MASTR."
A blinking cursor will appear after the TO: prompt on the display panel.
3. Press "ALL" and then press "ENTER."
The students will see the Instructor’s screen and the movements of the Instructor’s mouse.
To return control of the Student Computers to the students... 1. Press "FROM" on the Keypad.
To capture one student's screen and display it on the Instructor’s screen... 1. Press "FROM" on the Keypad.
2. Enter the student’s computer # (located on the back of the table where the student monitor is sitting).
3. Press "MASTR" and then press "ENTER."
To capture one student’s screen, keyboard, and mouse to the Instructor Computer... 1. Press "KB" on the Keypad.
A blinking cursor will appear after the KB: prompt.
2. Enter the number of the student’s computer that you want to capture and press "ENTER."
To return a student's screen, keyboard, and mouse to the student... 1. Press "KB" on the Keypad.
To return control of a student’s computer to the student... 1. Press "FROM" on the Keypad.
To capture a student's screen and display it to the entire class... 1. Press "FROM" on the Keypad.
2. Enter the student’s computer #."
3. Press "ALL" after the "TO" prompt and press "ENTER."
To return control of the student’s computer to the student... 1. Press "FROM" on the Keypad. 
To show a video... 1. Insert VHS tape into the VCR.
NOTE: The VCR will turn "ON" automatically if it is not already "ON."
2. Press "RIGHT MONITOR POWER" on the Touch Panel if the RIGHT TV monitor
is not "ON."
3. Press "LEFT MONITOR POWER" if the LEFT TV monitor is not "ON."
4. Press "RIGHT SOURCE."
5. Press "LOCAL VCR."
6. Press "PREVIOUS MENU."
7. Press "LEFT SOURCE."
8. Press "LOCAL VCR."
9. Press "PREVIOUS MENU."
10. Press "PLAY" on the Touch Panel.
11. Adjust the volume to 38-40 by pressing the volume controls ( << or >>) on the Touch Panel.
12. To stop the tape, press "STOP" on the Touch Panel.
13. To rewind the tape, press "VIDEO TAPE" on the Touch Panel, and then on the VIDEO TAPE CONTROL screen press "REWIND."
14. To remove the tape, press "EJECT" on the VCR.

 

 

After class...
Step 1: Press "RIGHT MONITOR POWER" on the Touch Panel to turn the RIGHT TV monitor "OFF."
Step 2: Press "LEFT MONITOR POWER" on the Touch Panel to turn the LEFT TV monitor "OFF."
Step 3: Press "VCR POWER" to turn the VCR "OFF."
Step 4: Leave the Instructor Computer "ON."
Step 5: Leave the Student Computers "ON."
Step 6: Check to make sure the door WITHOUT the Omni lock is closed securely.
Step 7: Turn the lights off.
Step 8: Close the door with the Omni lock securely.